Home Shop About Me Tutorials Recipes Recipes

My Favorite Sewing Tip – Hemming Cotton and Cotton Blend Knits

Be sure to read my updated Hemming Tips here.

Sew Mama Sew is putting together a list of SMS Readers’ Favorite Sewing Tips so I thought now would be a great time to share some of the things I’ve learned about hemming knit fabrics. I love sewing with knit fabrics, and most of my patterns are designed to be sewn with cotton or cotton/polyester blend knits. Because of the stretchy nature of knits, sewing them requires a different approach than sewing wovens, but with the right tools, you can get great results. With the wrong tools, you might end up with wavy stretched out hems like this:

My method is definitely not the only method, but it’s what works best for me. I start with my iron and a can of spray starch.

I like to fold the hem up twice. I feel that the little extra thickness gives a nice look to the stitching and it helps keep stretching to a minimum. Spray the hem allowance on your fabric lightly with spray starch, fold up once and press, then fold up again and press. The starch will also help minimize stretching, and it washes right out when your project is completed. I prefer not to pin because I’ve found that pinning tends to stretch the fabric while you’re sewing. (There’s definitely a theme here. The less stretching, the nicer your hem will look.)

Many sewists use a twin needle for hemming knits. A twin needle is a great option because the way a twin needle stitches allows the fabric to stretch without the threads breaking. Unfortunately, I can never get the stitching on the back of the fabric to look nice with a twin needle, and I prefer to stitch along the hem on the inside. I’ve found that another great way to keep your stitches from breaking with stretching of the fabric is to put Woolly Nylon in the bobbin on your sewing machine.

The last, but maybe the most important, tool for hemming knits is a walking foot. A walking foot has built in feed dogs that move the top of the fabric at the same time and rate of speed as the feed dogs on the sewing machine move the bottom of the fabric. This makes a huge difference in how much your fabric stretches as it travels through your machine.

With Woolly Nylon in your bobbin and your walking foot attached to your machine, position your fabric in your machine with the wrong side facing you. Line your needle up close to the top edge of your hem and stitch all the way down. I check to see which guideline on my machine the bottom edge of the hem is on when I first start and then keep the bottom edge right against that line as I stitch. This way, your hem will be nice and straight on the right side of the fabric.


One other thing that you may have noticed is that I like to hem before I sew or serge my pieces together. It’s much easier to hem a flat piece of fabric and keep it from stretching than it is to sew over seams once the sewn item has been put together. I just tie off my serging or backstitch at the end of each seam when the item that I’m sewing is completed.

I hope that helps make sewing knits a little less intimidating. If you have any questions, just leave a comment, and I’ll try to answer them as quickly as I can!

Updating with some answers to your questions:
Tina asked, “Are walking foots relatively inexpensive?” My Kenmore actually came with a walking foot, so I wasn’t exactly sure how expensive they are. I did a couple of quick Google searches, and it looks like the average cost is around $25.

Steph T. and Sarah H. suggested using a ball point needle which is a very important tip that I left out.

Alisa asked, “You just use a regular straight stitch?” and “When you wind the woolly nylon onto the bobbin do you just do it the way you would normally wind it? You don’t have to change tension or anything?” Yes, I just use a regular straight stitch with WN in the bobbin, and I no longer have any problems with the threads breaking. I wind the WN in the bobbin almost the same way that I would wind normal thread. I place the cone of WN in a coffee cup off to the side of my machine and pull it up through the tension disk. Then I tie a piece of regular thread to the end of the WN and use it to pull the end through the hole in the bobbin and wind it up as usual.

the4rs asked, “Do they make walking feet for older machines, mine Elna is from 1960’s?” My trusty Google search found that Sewing Supply Warehouse carries a universal walking foot. You just have to know whether your machine has a low, high or slant shank.

I hope those answers help. Keep the questions coming, and I’ll keep answering!

Print Friendly, PDF & Email

22 Responses to My Favorite Sewing Tip – Hemming Cotton and Cotton Blend Knits


    About Me



    Fishsticks Designs Pattern Shop

    Fishsticks Designs Tutorials
Explore

Subscribe



    Charity Patterns
Subscribe

The Tank

Bibs Tutorial

The Sleepbag

Drawstring Tute

Totally Terrific Ties
Recipes

Game Day Dip

GF Brownies

Granola Cookies